Skip to main content

782 results for 'joint system'

Categories
Brands
Popular Tools , Triton Tools , Incra
    Brazing Alloy Pushed Out of the Brazing Joint(Page)

    30x picture with our Proscope.   

    Machine Coolant Filter Systems Annual Cost and Payback(Page)

    Adding Machine Coolant Filtration Systems in a Carbide Tool Grinding Operation A shop with six grinders for saws and tools bought six filter units for $9,000.  They bought an additional $600 in...

    Machine Coolant Cleaning Systems(Page)

    Machine Coolant Cleaning Systems  Contaminated machine coolant are directly responsible for 70% to 90% of machine tool wear and failure.  A filter system that removes contaminants as they...

    Machine Coolant Filter Systems Customer Reviews(Page)

    Customers Love Our Machine Coolant Filtration Systems

    Effectiveness of Machine Coolant Filtration Systems(Page)

    The concept is to build extremely efficient units that sell for as little as possible.  We have done our best to design sturdy and reliable filter units that work well and cost less.  For...

    3 Easy Ways to Cut Mortises(Post)

    Mortise and tenon joints are regarded as one of the toughest types of joinery you can use for your woodworking projects. These joints are often associated with fine furniture making due the critical

    Advanced Brazing Training(Page)

    Deliverables on Previous Projects Eliminate tungsten carbide breakage entirely Reduce tungsten carbide braze failure to six sigma (3 parts per million)

    Cutter Failure(Page)

     Bad Surfaces And Too Much Heat   

    Braze Failure(Page)

     Solutions to Brazing Problems (This is an overview article largely based on customer reports.  Most of this is covered in much greater depth with photographs in other articles and in...

    Brazing with Propane(Page)

    Brazing Torch - 1300 F with a Bernzomatic Propane Torch  Here is the answer to whether you can braze with a propane / air torch.   You can but you have to control the environment so...

    Tungsten Carbide Automatic Brazing Standards(Page)

    Brazing Standards for Tungsten Carbide in Automatic Systems From the book Building Superior Brazed Tools  Buy the Book

    Saw Blade Analysis on a Bad Saw Blade(Page)

    John Gammelgard of Weyerhaeuser is a really good saw filer.  His command of analytical data is truly impressive.  Anyway someone sold John a saw blade that didn’t run well.  It came to...

    Brazing Carbide(Page)

    Buy Carbide Braze Alloy or Carbide Brazing Services  <

    Types of Filters for Filter Units(Page)

    There are several types of filters for machine Coolant Filtration.  The infomration below can help you decide which type of filter might work best for your chosen coolant management program...

    Router Bit Glossary(Page)

    Abrasive Routers  These routers are designed to cut abrasive materials such as tile and fiberglass. Sometimes configured in diamond pattern.   Air Cleaner (Air Purifier) A...

    Bandsaw Blade Brazing(Post)

    Bandsaw (Band Saw) Blade Brazing Six Easy Steps Clean and bevel the blade ends  Clamp blade ends to the fixture Spread the flux Braze Anneal Remove excess alloy Size of Blade With a very small, nar

    Calculating the Amount of Brazing Alloy to use(Page)

    Braze joints are strongest at about 0.0005” (1/2 of one –thousandth of an inch) but this is not a good standard for two main reasons: As the braze joint gets thicker it provides significant...

    When and Why to Fine Filter Machine Coolant(Page)

    For most purposes flat bed, cyclone, centrifugal and similar filter systems may be more than adequate.  There are some situations where fine filtering is a definite advantage.  Refer back...

    Holes in Braze Alloy(Page)

    The surface treatment on the carbide did not stick to the carbide.   There is the gray film on top of braze alloy. There are a great number of bubbles on the braze alloy which are probably...

    Bandsaw Blade Brazing(Page)

    Bandsaw (Band Saw) Blade Brazing   Clean and bevel the blade ends  Clamp blade en

!