Loading... Please wait...
| Outside Diameter | Inside Diameter | Application | Part # |
|---|---|---|---|
| 1/4" | 1/8" | B1A | |
| 3/8" | 1/8" | B1 | |
| 3/8" | 3/16" | B2 | |
| .490" | 3/16" | for resharps (undersize) | B3U |
| .490" | 1/4" | for resharps (undersize) | B9U |
| 1/2" | 3/16" | Standard | B3 |
| 1/2" | 3/16" | Non-Mar Nylon Sleeve | B3S |
| 1/2" | 3/16" | Euro-Square | B3SQ |
| 1/2" | 3/16" | Teflon® Shields | B3T |
| 1/2" | 1/4" | B9 | |
| 5/8" | 3/16" | B7 | |
| 5/8" | 1/4" | B6 | |
| 5/8" | 5/16" | B27 | |
| 11/16" | 3/16" | B14 | |
| 3/4" | 3/16" | B8 | |
| 3/4" | 3/16" | Euro-Square | B8SQ |
| 3/4" | 1/4" | B4 | |
| 3/4" | 5/16" | B20 | |
| 3/4" | 1/2" | B19 | |
| 13/16" | 3/16" | B15 | |
| 7/8" | 3/16" | B28 | |
| 7/8" | 1/4" | B21 | |
| 7/8" | 5/16" | B5 | |
| 7/8" | 3/8" | B12 | |
| 7/8" x 10° | 3/16" | Non-Mar Nylon Sleeve | BB300 |
| 1" | 3/16" | B29 | |
| 1 1/8" | 5/16" | B25 | |
| 1 1/8" | 1/2" | B11 | |
| 1 1/4" | 1/2" | B16 | |
| 1 3/8" | 5/16" | B26 | |
| 1 3/8" | 1/2" | B17 | |
| 1 1/2" | 1/2" | B18 | |
| 1 7/8" | 1/2" | B24 |
Retaining Collars used when bearings are added to the shanks of router bits for following templates.
| Shank Diameter | Outside Diameter | Part Number |
|---|---|---|
| 1/4" | 7/16" | LC-1/4 |
| 1/2" | 11/16" | LC-1/2 |
Use this kit to vary the horizontal cutting depth of router bits with bearing pilots. Great for stepping in to finish depth by controlled increments.
Contains B2 (3/8"), B3 (1/2"), B7 (5/8"), B8 (3/4") Bearings and 3/32" Hex Key Wrench
This handy kit inludes spare bearings, screws, and wrench to replace bearings on most bits.
Includes five B3 (1/2 x 3/16) and two B2 (3/8 x 3/16) bearings, ten 54025S Screws, and a 3/32 Hex Key Wrench.
Great for replacement bearings and screws - Plus this generous bearing assortment allows you to vary your cutting depths and change your profiles. Also contains lock collars and bearings for adding bearing guides to the shanks of your standard bits for following templates. Contains:
New Products
All prices are in USD Copyright 2025 Carbide Processors. Sitemap | Website by oBundle
e, but the one adaptor allows me to use annual cutters in an older mag drill, several different drill presses and milling machines without having to own separate adaptors with shanks that match several morse taper sizes and R8 tooling. Read LessRead less about This is a well machined adaptor that
e Ridgid cast iron table and the Incra fence per the Incra directions. It all works really well. The set up took a little while but it’s sweet! I have done probably 50 cuts and each time I measure with a caliper and it’s dead on front to back on the board I am cutting. I think I am within .004 between blade and fence discrepancies. So for a Ridgid R4512 I’ll take it. Now I have a $1000 package that can hang in terms of accuracy with a nicer cabinet saw. Read LessRead less about So I added the TS-LS 32” to my
, the deal was too good to ignore and figured I would challenge any irregularities with the credit card company later. I also located a coupon code that made the price unbeatable. It must be stated, the expected delivery time on this particular unit was 6 weeks out, adding to my concern. This is the same time frame advised on the Incra web site as well. At probably 5 weeks, I was thrilled to receive delivery notice emails. The large unit came in pristine condition and packaged extremely well. I WILL NOT HESITATE TO BUY FROM CARBIDE PROCESSORS IN THE FUTURE. Thank you for the fantastic deal! Read LessRead less about I had been looking for several weeks
