Skip to main content

8162 results for 'brake point drill bit'

Categories
Brands
Whiteside , Triumph Twist Drill , bormax-famag , Wera , Southeast Tool , Felo , Bondhus , Carbide Processors , Woodpeckers , HTC Tool , Chapman MFG , Incra , Wiha
    CSM Saw Steel(Page)

    The steel in a saw blank must be high quality, machined, heat-treated and handled properly. There are two grades of steel most generally used in plates. These are plain carbon steel and nickel alloy...

    Gumming Saws(Page)

    by Lowell Freeborn Saw gumming is an operation that must be performed on all saws to be retipped.  It must be done accurately so the saw does not run out of balance and the tip recesses...

    CSM Gumming(Page)

    Saw gumming is an operation that must be performed on all saws to be retipped.  It must be done accurately so the saw does not run out of balance and the tip recesses are all the same depth...

    Advanced Brazing Training(Page)

    Deliverables on Previous Projects Eliminate tungsten carbide breakage entirely Reduce tungsten carbide braze failure to six sigma (3 parts per million)

    Books (Page)

    Books Available for Purchase

    Machine Coolant Filtering Successes(Page)

    The shop is West Coast Saws in Tacoma WA. at 2725 S. Ash St and it is owned by Brian Wallinger.   They grind saws and tools within one - one thousandth of an inch and have a computerized...

    Filtration Glossary continued n-r(Page)

    Machine Coolant Filtration Glossary Here is a glossary of Filtration Terms and their meanings.  Please refer to the

    CSM Face Grinding(Page)

    More saws are literally butchered by facing improperly than by any other grinding operation.  In the first place, when a saw is first manufactured it has cutting geometry that is designed to...

    Saw Blade Wear Cutting Gypsum Board(Page)

    Saw Blade Wear Cutting Gypsum   End of gypsum board – notice saw marks &nbs

    Bad Surface and Gumming(Page)

       Chrome Plating Not Gummed Out of Notch   

    Saw Blade Face Grinding(Page)

    by Lowell Freeborn More saws are literally butchered by facing improperly than by any other grinding operation.  In the first place, when a saw is first manufactured it has cutting geometry...

    Machine Coolant Sump Cleaning(Page)

    (This is a cleaning method for cleaning machine coolant sumps running water based machine coolants.  This is, perhaps, overkill in many cases but how much of this to do is your decision. ...

    How Carbide Wears(Page)

    Carbide Wear From the book Building Superior Brazed Tools    Buy the Book  

    Diamond Grinding(Page)

    by Lowell Freeborn  The first question you should ask yourself is: What do I expect from a diamond wheel? Your answer should be a wheel that removes carbide fast and cool. Think this over very...

    CSM Diamond Grinding(Page)

    The first question you should ask yourself is: What do I expect from a diamond wheel? Your answer should be a wheel that removes carbide fast and cool. Think this over very carefully and do not get...

    When and Why to Fine Filter Machine Coolant(Page)

    For most purposes flat bed, cyclone, centrifugal and similar filter systems may be more than adequate.  There are some situations where fine filtering is a definite advantage.  Refer back...

    Diamond Grinding Saw Blades(Page)

    Lowell Freeborn The first question you should ask yourself is: What do I expect from a diamond wheel? Your answer should be a wheel that removes carbide fast and cool. Think this over very...

    Machine Coolant Filter Units Owners Manual(Page)

    Owner’s Manual CP 2002 (also CP 2002 Wall Mount) & CP 2020 machine coolant Filtering Systems

    Types of Machine Coolant Disposal(Page)

    WARNING:  Do not take the following as being absolutely correct or as being all you need to know.   These were really good guidelines when I wrote them but laws change all the...

    Band Saw Troubleshooting(Post)

    Common Band Saw problems and how to solve them.  When it comes to learning what works and what doesn’t, nothing beats experience.  MK Morse has over 45 years of experience in the Band Saw business.  O

!