Chamfer bits are used to cut a beveled edge on the profile. They can also be used to create angled edges for constructing boxes. For a 4-sided box, use a 45 degree chamfer bit. For a 6 sided box, use a 30 degree chamfer bit and for an 8 sided box use a 22 1/2 degree chamfer bit. Whiteside Chamfer bits have a reputation for quality and dependability. Choose from one of the standard Whiteside Chamfer bits below, or get a quote on a custom Chamfer bit.
Place your order for Whiteside Router bits before 2:30pm ET Mon-Fri to have your order ship same Day!
"A" Degree of Angle | "B" Cutting Length | "C" Cutting Height | Overall Length | Part Number |
---|---|---|---|---|
1/4" SHANK | ||||
45° | 5/8" | 7/16" | 2" | 2302 |
1/2" SHANK | ||||
45° | 5/8" | 7/16" | 2 1/4" | 2305 |
45° | 1 1/16" | 3/4" | 2 1/2" | 2306 |
45° | 1 1/2" | 1 1/16" | 3" | 2310 |
Bearing Number: B3
Choose from a great selection of Whiteside Edge Bevel bits with varying bevel angles and cutting lengths and depths. Choose from one of the standard Whiteside Edge Bevel Bits below, or get a quote on a custom Edge Bevel Bit.
"A" Degree of Angle | "B" Cutting Length | "C" Cutting Height | Overall Length | Part Number |
---|---|---|---|---|
1/4" SHANK | ||||
7° | 3/8" | 3/8" | 2 1/8" | * 2298 |
15° | 1/2" | 1/2" | 2" | 2300 |
15° | 1/4" | 1/4" | 2" | * 2300A |
25° | 9/16" | 1/2" | 2" | 2301 |
30° | 7/8" | 3/4" | 2 3/4" | (1) 2308 |
1/2" SHANK | ||||
15° | 1" | 15/16" | 2 3/4" | (3) 2325 |
22 1/2° | 15/16" | 7/8" | 2 3/4" | (2) 2307 |
30° | 7/8" | 3/4" | 2 3/4" | (1) 2309 |
60° | 1" | 9/16" | 2 1/4" | 2318 |
Bearing Number: B3 |
* Used on Laminate Trim |
(1) Used for six sided boxes |
(2) Used for eight sided boxes |
(3) Used for twelve sided boxes |
All prices are in USD Copyright 2025 Carbide Processors. Sitemap | Website by oBundle
e, but the one adaptor allows me to use annual cutters in an older mag drill, several different drill presses and milling machines without having to own separate adaptors with shanks that match several morse taper sizes and R8 tooling. Read LessRead less about This is a well machined adaptor that
e Ridgid cast iron table and the Incra fence per the Incra directions. It all works really well. The set up took a little while but it’s sweet! I have done probably 50 cuts and each time I measure with a caliper and it’s dead on front to back on the board I am cutting. I think I am within .004 between blade and fence discrepancies. So for a Ridgid R4512 I’ll take it. Now I have a $1000 package that can hang in terms of accuracy with a nicer cabinet saw. Read LessRead less about So I added the TS-LS 32” to my
, the deal was too good to ignore and figured I would challenge any irregularities with the credit card company later. I also located a coupon code that made the price unbeatable. It must be stated, the expected delivery time on this particular unit was 6 weeks out, adding to my concern. This is the same time frame advised on the Incra web site as well. At probably 5 weeks, I was thrilled to receive delivery notice emails. The large unit came in pristine condition and packaged extremely well. I WILL NOT HESITATE TO BUY FROM CARBIDE PROCESSORS IN THE FUTURE. Thank you for the fantastic deal! Read LessRead less about I had been looking for several weeks