Skip to main content

402 results for 'braze and alloy'

Did you mean: brake alloi Refine Search
Categories
    Bandsaw Blade Brazing(Post)

    Bandsaw (Band Saw) Blade Brazing Six Easy Steps Clean and bevel the blade ends  Clamp blade ends to the fixture Spread the flux Braze Anneal Remove excess alloy Size of Blade With a very smal ...

    Carbide Braze Failure Due To Machining Of the Steel Holder(Post)

    The Machining of the Steel Holders caused the braze joint to fail.  Below is an analysis of what happened. This project was the brazing of a rectangular blank into a steel holder for use as a sc ...

    Simple Solutions to Brazing Problems(Page)

    About 80 - 90% that these answers will solve these problems.  If you want more details you can go to our Braze Failure Analysis page.  Or buy the books.  You can also call 1-800 346- ...

    Steel Brazing- Brazing to Laser Cut Steel(Page)

     Why You Need To Gum Saw Plate  (You can buy saw plate that has been sandblasted to remove the heat affected zone.  This can work but it takes a lot of sandblasting.)    ...

    Brazing Tungsten Carbide in a Notch(Page)

    Method #1 is the most common. Method #2 is easiest, cheapest, most reliable and generally works best.  Method #3 can give a little advantage but that is rarely needed in this kind of an applicat ...

    How Flux Affects Brazing(Page)

    Good & Bad Tips    Good           Bad     Good parts have an even flow to all four corners.  ...

    Brazing Process(Page)

    Definitions Brazing is the joining of two dissimilar materials using a third material.  brazing alloying and brazing are the same thing except the brazing alloying takes place below 840 F and b ...

    Brazing Tungsten Carbide- Health and Safety(Page)

    Brazing Tungsten Carbide - Health and Safety From the book Building Superior Brazed Tools    Buy the Book  Contents Standard Procedures Possible Damage “Safe” B ...

    CSM Brazing(Page)

    This operation actually consists of silver soldering and requires practice to become efficient at it. There are two generally accepted methods. One is to pre-tin the carbide tip by applying flux to i ...

    Brazing Ceramics(Page)

    ...

    Cleaning Steel (Page)

    Cleaning Steel Before Brazing There are many differing opinions in this area. I recommend Easy Off Oven Cleaner for cleanliness test because it is easy, cheap, effective and everyone knows it is dan ...

    Router Bit Failure(Page)

      Problems Numerous holes and voids Areas where the braze alloy did not stick to the steel Areas where the braze alloy did not sick to the carbide     &nb ...

    Cutter Failure(Page)

     Bad Surfaces And Too Much Heat    Several problems  Sloppy brazing  - the braze alloy ran all over the steel  Uneven heating.  Th ...

    Debarker Tip Breakage(Page)

      Induction Brazing   History There is greatly increased breakage coincident with the switch in brazing alloys from BAg-3 (50% with Cadmium) to BAg-24 (50% Cadmium free).   ...

    Carbide Surface Treatment(Page)

    From the book Building Superior Brazed Tools   Buy the Book   Graph shows that the ECP surface treatment doubled joint strength on the average and dramatically increased process re ...

    Welding Carbide(Page)

    Welding Tungsten Carbide  From the book Building Superior Brazed Tools  Buy the Book  Weldable tungsten carbide is generally used to mean the joining of tungsten carbide to steel wit ...

    Can Cleaners Harm Saw Blades(Page)

    Also See: Soaking Saw Tips in Oven Cleaner First, there are thousands of grades of carbide so discussing the properties of carbide is like discussing the properties of wood. Therefore, I suppos ...

    Technical Info(Page)

    We offer professional services in the following areas:  Woodworking Carbide Parts Brazing Carbide Router Bits Saw Blades Machine Coolant Custom Tooling To inquire about the profe ...

    Pretin(Page)

    Pretin, Pretinning, or Tinning   Tinning, Pretinning or Pretin is applying brazing alloy to one or both parts separately then putting the parts together and heating them to complete th ...

    Saw Tip Breakage(Page)

    Saw Tip Breakage Drawings These drawings are not to be taken as absolutely accurate in all instances.  However they have been very helpful in the great majority of cases.    ...

!