Loading... Please wait...| Cermet vs. Carbide saw tests | |||
| Run at | |||
| Date | |||
| Machine | |||
| Operator | |||
| Saw description | carbide data | Saw description | cermet data |
| Carbide | Cermet | ||
| Plate hardness Rc | Plate hardness Rc | ||
| Plate thickness | Plate thickness | ||
| Plate finish | Plate finish | ||
| Outside diameter | Outside diameter | ||
| Bore diameter | Bore diameter | ||
| Number Teeth | Number Teeth | ||
| Hook | Hook | ||
| Clearance | Clearance | ||
| Sharpness | Sharpness | ||
| Spacing | Spacing | ||
| Gullet area | Gullet area | ||
| Insert notch length | Insert notch length | ||
| Angle | Angle | ||
| Carbide tip | Cermet tip | ||
| Kerf | Kerf | ||
| Hook | Hook | ||
| Side clearance | Side clearance | ||
| Radial clearance angle | Radial clearance angle | ||
| Tangential clearance angle | Tangential clearance angle | ||
| Top clearance angle | Top clearance angle | ||
| Tooth side clearance variation | Tooth side clearance variation | ||
| Tooth top run out | Tooth top run out | ||
| Tooth length | Tooth length | ||
| Tooth thickness | Tooth thickness | ||
| Rim speed initially | Rim speed initially | ||
| Second rim speed | Second rim speed | ||
| Third rim speed | Third rim speed | ||
| How fed | How fed | ||
| Material | Material | ||
| name | name | ||
| grade | grade | ||
| supplier | supplier | ||
| tradename | tradename | ||
| Results | Results | ||
| Best rim speed | Best rim speed | ||
| How fast fed for best results | How fast fed for best results | ||
| Maximum Amount fed | Maximum Amount fed | ||
| Power usage | Power usage | ||
| Sound level | Sound level | ||
| Cut quality | Cut quality | ||
| naked eye | naked eye | ||
| magnification | magnification | ||
| Edge chipping | Edge chipping | ||
| Blow out | Blow out | ||
| Tear out | Tear out | ||
| NW Research Institute, Inc. / Carbide Processors, Inc. | |||
| 3847 S. Union Ave. Tacoma, WA. 98409 | |||
| 253 476-1338 president@carbideprocessors.com | |||
All prices are in USD Copyright 2025 Carbide Processors. Sitemap | Website by oBundle
e, but the one adaptor allows me to use annual cutters in an older mag drill, several different drill presses and milling machines without having to own separate adaptors with shanks that match several morse taper sizes and R8 tooling. Read LessRead less about This is a well machined adaptor that
e Ridgid cast iron table and the Incra fence per the Incra directions. It all works really well. The set up took a little while but it’s sweet! I have done probably 50 cuts and each time I measure with a caliper and it’s dead on front to back on the board I am cutting. I think I am within .004 between blade and fence discrepancies. So for a Ridgid R4512 I’ll take it. Now I have a $1000 package that can hang in terms of accuracy with a nicer cabinet saw. Read LessRead less about So I added the TS-LS 32” to my
, the deal was too good to ignore and figured I would challenge any irregularities with the credit card company later. I also located a coupon code that made the price unbeatable. It must be stated, the expected delivery time on this particular unit was 6 weeks out, adding to my concern. This is the same time frame advised on the Incra web site as well. At probably 5 weeks, I was thrilled to receive delivery notice emails. The large unit came in pristine condition and packaged extremely well. I WILL NOT HESITATE TO BUY FROM CARBIDE PROCESSORS IN THE FUTURE. Thank you for the fantastic deal! Read LessRead less about I had been looking for several weeks
